Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-10V, Lap Condition: 0-5 %, Seal Material: EPDM, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-10V, Lap Condition: 0-5 %, Seal Material: NBR, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-10V, Lap Condition: 0-5 %, Seal Material: Viton, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-10V, Lap Condition: 0-5 %, Seal Material: EPDM, Fluid Type: Skydrol, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-10V, Lap Condition: 0-5 %, Seal Material: NBR, Fluid Type: Skydrol, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-10V, Lap Condition: 0-5 %, Seal Material: Viton, Fluid Type: Skydrol, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-20mA, Lap Condition: 0-5 %, Seal Material: EPDM, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-20mA, Lap Condition: 0-5 %, Seal Material: NBR, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-20mA, Lap Condition: 0-5 %, Seal Material: Viton, Fluid Type: Red Oil, Enable Mode: No
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-10V , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:EPDM , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-10V , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:NBR , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-10V , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:Viton , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Skydrol , Input Signal:+/-10V , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:EPDM , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Skydrol , Input Signal:+/-10V , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:NBR , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Skydrol , Input Signal:+/-10V , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:Viton , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:EPDM , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:NBR , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:Viton , Weight:1500 .
If you currently use, or are considering, a Servo Valve currently in the market, we are confident that we have a suitable alternative, select below or, if the product is not listed, then Contact Us
If you are considering a Pump or Subsystem, then please call us to discuss on 
01761 252 650
40% Fewer Parts25% Higher Flow400% Smaller200%+ FasterHigher quality hydraulic valves and systems available at a lower price than more established units.
Find Out More
The Domin direct drive hydraulic servo valves use the most advanced design, analysis, test and manufacturing technologies. This enabled an innovative step change in performance of DDV technology.
The direct drive hydraulic valves use the most advanced design, analysis, test and manufacturing technologies. Giving you are greener, cleaner, efficient and reliable servo systems and valves.
Find Out More
* Based on a S6 Pro Valve which will save 17 tonnes of Carbon Dioxide over 15 years.
1. Concept Generation
The product specification is generated with customers, market analysis and engineering calculations at its core. Technology building blocks are combined to create a conceptual design. Key parts are sized, with high-level performance predictions calculated.
2. Design and simulation
Using the latest tools, the concept design is developed and matured. Simulation and analysis is used to validate the mechanical and functional performance, and electronics hardware and firmware developed to control the system.
3. Prototype Manufacture
The latest rapid manufacturing techniques are used to quickly deliver a working prototype unit, with manufacturing process development occurring in tandem in our advanced manufacturing facility.
4. Development & Validation
Prototype units go through a series of representative validation tests to characterise, optimise and validate performance, reliability and operability.
5. Industrialisation
Our focus is always on making a product that delivers real benefit in the real world, and this means focus on ability to ramp to production volume, at a cost that is commercially feasible. Our production facility delivers >20,000 parts per annum, and is constantly expanding.
The product specification is generated with customers, market analysis and engineering calculations at its core. Technology building blocks are combined to create a conceptual design. Key parts are sized, with high-level performance predictions calculated.
Using the latest tools, the concept design is developed and matured. Simulation and analysis is used to validate the mechanical and functional performance, and electronics hardware and firmware developed to control the system.
The latest rapid manufacturing techniques are used to quickly deliver a working prototype unit, with manufacturing process development occurring in tandem in our advanced manufacturing facility.
Prototype units go through a series of representative validation tests to characterise, optimise and validate performance, reliability and operability.
Our focus is always on making a product that delivers real benefit in the real world, and this means focus on ability to ramp to production volume, at a cost that is commercially feasible. Our production facility delivers >20,000 parts per annum, and is constantly expanding.
My Account
Cart
