The Domin S10 Pro is a single-stage DDV which combines high flow, excellent dynamics, strong chipshear, and low power consumption.
A single-stage valve has the advantage of being able to position the spool independent of supply pressure and without wasting high-pressure fluid.
The S10 Pro has been designed to sustain high bandwidth operation at exceptional flows without significant limitation of operating pressures or duty cycles.
Please browse our range below, if you have any specific adjustments or customisations you want, then please contact us direct by email or through the chat.
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: 4-20mA, Lap Condition: 0-5 %, Seal Material: EPDM, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: 4-20mA, Lap Condition: 0-5 %, Seal Material: Viton, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: 4-20mA, Lap Condition: 0-5 %, Seal Material: NBR, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: 4-20mA, Lap Condition: 0-5 %, Seal Material: EPDM, Fluid Type: Red Oil, Enable Mode: Yes
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: 4-20mA, Lap Condition: 0-5 %, Seal Material: Viton, Fluid Type: Red Oil, Enable Mode: Yes
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: 4-20mA, Lap Condition: 0-5 %, Seal Material: NBR, Fluid Type: Red Oil, Enable Mode: Yes
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-20mA, Lap Condition: 0-5 %, Seal Material: EPDM, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-20mA, Lap Condition: 0-5 %, Seal Material: Viton, Fluid Type: Red Oil, Enable Mode: No
Weight: 1500 g, Rated Flow: 110-250 lpm, Power Off Position: Centre, Connector: EN 175201-804 6 + PE, Input Signal: +/-20mA, Lap Condition: 0-5 %, Seal Material: NBR, Fluid Type: Red Oil, Enable Mode: No
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:4-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:EPDM , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:4-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:Viton , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:4-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:NBR , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:Yes , Fluid Type:Red Oil , Input Signal:4-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:EPDM , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:Yes , Fluid Type:Red Oil , Input Signal:4-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:Viton , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:Yes , Fluid Type:Red Oil , Input Signal:4-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:NBR , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:EPDM , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:Viton , Weight:1500 .
Connector:EN 175201-804 6 + PE , Enable Mode:No , Fluid Type:Red Oil , Input Signal:+/-20mA , Lap Condition:0-5 , Power Off Position:Centre , Rated Flow:110-250 , Seal Material:NBR , Weight:1500 .
Higher quality available at a lower price than more established units.
Find Out MoreThe Domin direct drive servo valves use the most advanced design, analysis, test and manufacturing technologies. This enabled an innovative step change in performance of DDV technology.
The direct drive valves use the most advanced design, analysis, test and manufacturing technologies.
Find Out More
* Based on a S6 Pro Valve which will save 17 tonnes of Carbon Dioxide over 15 years.
1. Concept Generation
The product specification is generated with customers, market analysis and engineering calculations at its core. Technology building blocks are combined to create a conceptual design. Key parts are sized, with high-level performance predictions calculated.
2. Design and simulation
Using the latest tools, the concept design is developed and matured. Simulation and analysis is used to validate the mechanical and functional performance, and electronics hardware and firmware developed to control the system.
3. Prototype Manufacture
The latest rapid manufacturing techniques are used to quickly deliver a working prototype unit, with manufacturing process development occurring in tandem in our advanced manufacturing facility.
4. Development & Validation
Prototype units go through a series of representative validation tests to characterise, optimise and validate performance, reliability and operability.
5. Industrialisation
Our focus is always on making a product that delivers real benefit in the real world, and this means focus on ability to ramp to production volume, at a cost that is commercially feasible. Our production facility delivers >20,000 parts per annum, and is constantly expanding.
The product specification is generated with customers, market analysis and engineering calculations at its core. Technology building blocks are combined to create a conceptual design. Key parts are sized, with high-level performance predictions calculated.
Using the latest tools, the concept design is developed and matured. Simulation and analysis is used to validate the mechanical and functional performance, and electronics hardware and firmware developed to control the system.
The latest rapid manufacturing techniques are used to quickly deliver a working prototype unit, with manufacturing process development occurring in tandem in our advanced manufacturing facility.
Prototype units go through a series of representative validation tests to characterise, optimise and validate performance, reliability and operability.
Our focus is always on making a product that delivers real benefit in the real world, and this means focus on ability to ramp to production volume, at a cost that is commercially feasible. Our production facility delivers >20,000 parts per annum, and is constantly expanding.